347097180
|
0216000
|
2023-11-08
|
7 RUTLAND ROAD, SCARSDALE, NY, 10583
|
|
Inspection Type |
Planned
|
Scope |
Complete
|
Safety/Health |
Safety
|
Close Conference |
2023-11-08
|
Emphasis |
N: FALL, P: FALL
|
Violation Items
Citation ID |
01001 |
Citaton Type |
Serious |
Standard Cited |
19260100 A |
Issuance Date |
2024-01-12 |
Current Penalty |
1323.0 |
Initial Penalty |
2009.0 |
Final Order |
2024-02-08 |
Nr Instances |
1 |
Nr Exposed |
2 |
Related Event Code (REC) |
Imminent Danger |
Gravity |
1 |
FTA Current Penalty |
0.0 |
Citation text line |
Employees working in areas where there was a possible danger of head injury from impact, or falling or flying objects, or from electrical shock and burns, were not protected by protective helmets: 7 Rutland Road, Scarsdale - NY: Employees were exposed to head injuries while working below framing activities. The employees were not protected by hard hats or protective helmets, on or about, November 8th, 2023. |
|
Citation ID |
01002 |
Citaton Type |
Serious |
Standard Cited |
19260102 A01 |
Issuance Date |
2024-01-12 |
Current Penalty |
1765.0 |
Initial Penalty |
2679.0 |
Final Order |
2024-02-08 |
Nr Instances |
1 |
Nr Exposed |
1 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.102(a)(1): Eye and face protective equipment were not used when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents. A) 7 Rutland Road, Scarsdale - NY: An employee was exposed to eye/face injuries while using a pneumatic nail gun during framing work. The employee was not protected by eye/face protection, on or about, November 8th, 2023. |
|
Citation ID |
01003 |
Citaton Type |
Serious |
Standard Cited |
19260501 B13 |
Issuance Date |
2024-01-12 |
Current Penalty |
2647.0 |
Initial Penalty |
4018.0 |
Final Order |
2024-02-08 |
Nr Instances |
1 |
Nr Exposed |
1 |
Related Event Code (REC) |
Imminent Danger |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system, nor were employee(s) provided with an alternative fall protection measure under another provision of paragraph 1926.501 (b): A) 7 Rutland Road, Scarsdale - NY: An employee was exposed to fall hazards of approximately 11-feet while conducting framing work, without the use of harnesses, or other fall protection devices, on or about, November 8th, 2023. |
|
Citation ID |
01004 |
Citaton Type |
Serious |
Standard Cited |
19261053 B01 |
Issuance Date |
2024-01-12 |
Current Penalty |
1765.0 |
Initial Penalty |
2679.0 |
Final Order |
2024-02-08 |
Nr Instances |
1 |
Nr Exposed |
1 |
Related Event Code (REC) |
Imminent Danger |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.1053(b)(1): Portable ladders were used for access to an upper landing surface, the ladder side rails did not extend at least 3 feet above the upper landing surface to which the ladder is used to gain access: A) 7 Rutland Road, Scarsdale - NY: An employee was exposed to fall hazards of approximately 11-feet while using an extension ladder to access an upper level of a structure. The extension ladder that was used, did not extend at least 3 feet above the landing, on or about, November 8th, 2023. |
|
|
346671134
|
0216000
|
2023-01-14
|
RIDGE ROAD, BRONXVILLE, NY, 10708
|
|
Inspection Type |
Planned
|
Scope |
Complete
|
Safety/Health |
Safety
|
Close Conference |
2023-01-14
|
Emphasis |
L: FALL, P: FALL
|
|
345739502
|
0216000
|
2022-01-21
|
38- FRANKLIN RD., SCARSDALE, NY, 10583
|
|
Inspection Type |
Referral
|
Scope |
Complete
|
Safety/Health |
Safety
|
Close Conference |
2022-01-21
|
Emphasis |
L: FALL, L: FORKLIFT
|
Related Activity
Type |
Referral |
Activity Nr |
1857508 |
Safety |
Yes |
|
Type |
Inspection |
Activity Nr |
1573946 |
Safety |
Yes |
|
Violation Items
Citation ID |
01001 |
Citaton Type |
Serious |
Standard Cited |
19260451 G01 |
Issuance Date |
2022-03-23 |
Current Penalty |
3500.0 |
Initial Penalty |
4351.0 |
Nr Instances |
1 |
Nr Exposed |
2 |
Related Event Code (REC) |
Complaint |
Gravity |
10 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.451(g)(1): Employees on scaffolds more than 10 feet (3.1 m) above a lower level were not protected from falling to that lower level by fall protection established in paragraphs (g)(1)(i)-(vii) of this section: On or about: January 21, 2022 Location: 38 Franklin Rd, Scarsdale, New York 10583 a) Employees were working on a inadequate 5ft by 12ft temporary working platform approximately 20ft high without fall protection installing fascia board. Employees were exposed to fall hazard. |
|
Citation ID |
01002A |
Citaton Type |
Serious |
Standard Cited |
19260602 C01 VIII |
Issuance Date |
2022-03-23 |
Current Penalty |
3500.0 |
Initial Penalty |
4351.0 |
Nr Instances |
1 |
Nr Exposed |
2 |
Related Event Code (REC) |
Referral |
Gravity |
10 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.602(c)(1)(viii):A lift truck, equipped with vertical only, or vertical and horizontal controls elevatable with the lifting carriage or forks for lifting personnel, did not have the following precautions to include (A) Use of a safety platform firmly secured to the lifting carriage and/or forks (B) Means whereby personnel on the platform can shut off power to the truck (C) Protection from falling objects as indicated necessary by the operating conditions. On or about: January 21, 2022 Location: 38 Franklin Rd, Scarsdale, New York 10583 a) Employee was using a JLG1044C-54, series II rough terrain forklift to lift employees on a inadequate fabricated 5 ft by 12 ft temporary working platform to install fascia board. Unsecured platform fell with two employees causing injuries. |
|
Citation ID |
01002B |
Citaton Type |
Serious |
Standard Cited |
19260602 D |
Issuance Date |
2022-03-23 |
Abatement Due Date |
2022-06-30 |
Current Penalty |
0.0 |
Initial Penalty |
2486.0 |
Nr Instances |
1 |
Nr Exposed |
3 |
Related Event Code (REC) |
Referral |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.602(d): The employer did not certify that each operator had been trained and evaluated as required by paragraph 29 CFR 1910.178(l):Note: On or about: January 21, 2022 Location: 38 Franklin Rd, Scarsdale, New York 10583 a) Employee was not certified to operate a JLG1044C-54, series II rough terrain forklift. Forklift was used to lift employees on a inadequate fabricated 5 ft by 12 ft. temporary working platform to install fascia board. Inadequate temporary working platform fell with two employees causing injuries. |
|
|
340640051
|
0216000
|
2015-05-18
|
562/570 NORTH BEDFORD RD., BEDFORD HILLS, NY, 10507
|
|
Inspection Type |
Planned
|
Scope |
Complete
|
Safety/Health |
Safety
|
Close Conference |
2015-05-19
|
Emphasis |
P: FALL, L: FALL
|
Case Closed |
2017-08-23
|
Related Activity
Type |
Inspection |
Activity Nr |
1064347 |
Safety |
Yes |
|
Type |
Inspection |
Activity Nr |
1064384 |
Safety |
Yes |
|
Type |
Inspection |
Activity Nr |
1064365 |
Safety |
Yes |
|
Violation Items
Citation ID |
01001 |
Citaton Type |
Serious |
Standard Cited |
19260021 B02 |
Issuance Date |
2015-06-26 |
Abatement Due Date |
2015-07-23 |
Current Penalty |
1100.0 |
Initial Penalty |
2200.0 |
Final Order |
2015-07-24 |
Nr Instances |
5 |
Nr Exposed |
5 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe conditions and the regulations applicable to his work environment to control or eliminate any hazards or other exposure to illness or injury: Location: entiere site On or about: 5/18/15 a) Employees were exposed to hazards including lack of rebar protection and electrical hazards. The employees were not provided with general safety and health training. |
|
Citation ID |
01002 |
Citaton Type |
Serious |
Standard Cited |
19260404 B01 I |
Issuance Date |
2015-06-26 |
Current Penalty |
1100.0 |
Initial Penalty |
2200.0 |
Final Order |
2015-07-24 |
Nr Instances |
1 |
Nr Exposed |
5 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.404(b)(1)(i): General. The employer did not use either ground fault circuit interrupters as specified in paragraph (b)(1)(ii) of this section or an assured equipment grounding conductor program as specified in paragraph (b)(1)(iii) of this section to protect employees on construction sites. These requirements are in addition to any other requirements for equipment grounding conductors: location: site wide on or about: 5/18/15 a) Employees were using electrical equipment, including circular saws, while engaged in carpentry work. The employees were not provided with GFCI protection or an assured equipment grounding conductor program. |
|
Citation ID |
01003 |
Citaton Type |
Serious |
Standard Cited |
19260451 C02 V |
Issuance Date |
2015-06-26 |
Abatement Due Date |
2015-07-06 |
Current Penalty |
1100.0 |
Initial Penalty |
2200.0 |
Final Order |
2015-07-24 |
Nr Instances |
1 |
Nr Exposed |
1 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.451(c)(2)(v): Fork-lifts were used to support scaffold platforms while the entire platform was not attached to the fork and the fork-lift was moved horizontally while the platform was occupied: location: detailing building on or about: 5/18/15 a) An employee was working from a Lull rough terrain fork lift, while engaged in carpentry work. The plywood work platform was not attached to the forks. |
|
Citation ID |
01004 |
Citaton Type |
Serious |
Standard Cited |
19260701 B |
Issuance Date |
2015-06-26 |
Current Penalty |
1100.0 |
Initial Penalty |
2200.0 |
Final Order |
2015-07-24 |
Nr Instances |
12 |
Nr Exposed |
5 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.701(b): Reinforcing steel. All protruding reinforcing steel, onto and into which employees could fall, was not guarded to eliminate the hazard of impalement: location: detailing station on or about: 5/18/15 a) Employees were working above 12 unguarded rebar. |
|
Citation ID |
01005 |
Citaton Type |
Serious |
Standard Cited |
19261051 A |
Issuance Date |
2015-06-26 |
Current Penalty |
1100.0 |
Initial Penalty |
2200.0 |
Final Order |
2015-07-24 |
Nr Instances |
1 |
Nr Exposed |
1 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.1051(a): Stairway(s) or ladder(s) were not provided at all personnel points of access where there was a break in elevation of 19 inches (48 cm) or more, or no ramp, runway, sloped embankment, or personnel hoist was provided: location: detailing building on or about: 1/18/15 a) An employee used a wooden brace to climb down from a work platform. The employee was exposed to a fall of 8 feet 10 inches. |
|
Citation ID |
01006 |
Citaton Type |
Serious |
Standard Cited |
19261053 B01 |
Issuance Date |
2015-06-26 |
Current Penalty |
1100.0 |
Initial Penalty |
2200.0 |
Final Order |
2015-07-24 |
Nr Instances |
1 |
Nr Exposed |
5 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.1053(b)(1): Portable ladders were used for access to an upper landing surface and the ladder side rails did not extend at least 3 feet (.9 m) above the upper landing surface to which the ladder was used to gain access: location: detailing building on or about: 5/18/15 a) Employees were gaining access to and from the roof using a ladder that did not extend above the landing surface. |
|
Citation ID |
01007 |
Citaton Type |
Serious |
Standard Cited |
19261060 A |
Issuance Date |
2015-06-26 |
Abatement Due Date |
2015-07-23 |
Current Penalty |
1100.0 |
Initial Penalty |
2200.0 |
Final Order |
2015-07-24 |
Nr Instances |
5 |
Nr Exposed |
5 |
Gravity |
5 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.1060(a): The employer did not provide a training program for each employee using ladders and stairways, that enabled employee to recognize hazards related to ladders and stairways, and that trained each employee in the procedures to be followed to minimize these hazards: location: entire site on or about: 5/18/15 a) Employees were using portable ladders while engaged in carpentry work. The employees were not provided with ladder safety training. |
|
Citation ID |
02001 |
Citaton Type |
Repeat |
Standard Cited |
19260501 B01 |
Issuance Date |
2015-06-26 |
Current Penalty |
3080.0 |
Initial Penalty |
6160.0 |
Final Order |
2015-07-24 |
Nr Instances |
1 |
Nr Exposed |
5 |
Gravity |
10 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.501(b)(1): Each employee on a walking/working surface with an unprotected side or edge which was 6 feet (1.8 m) or more above a lower level was not protected from falling by the use of guardrail systems, safety net systems, or personal fall arrest systems. location: detailing building on or about: 5/18/15 a) Employees were engaged in carpentry work, 14 feet above the ground. The employees were not protected from falling to the ground below. The Koibil Construction Corporation was previously cited for a violation of this occupational safety and health standard or its equivalent standard 1926.501(b)(13), which was contained in OSHA inspection number 1012116, citation number 1, item number 2a and was affirmed as a final order on 1/20/2015, with respect to a workplace located at 33 Maple Ave., Greenwich, CT. |
|
Citation ID |
02002 |
Citaton Type |
Repeat |
Standard Cited |
19260503 A01 |
Issuance Date |
2015-06-26 |
Abatement Due Date |
2015-07-23 |
Current Penalty |
3068.0 |
Initial Penalty |
6160.0 |
Final Order |
2015-07-24 |
Nr Instances |
5 |
Nr Exposed |
5 |
Gravity |
10 |
FTA Current Penalty |
0.0 |
Citation text line |
29 CFR 1926.503(a)(1): The employer did not provide a training program for each employee who might be exposed to fall hazards. The program shall enable each employee to recognize the hazards of falling and shall train each employee in the procedures to be followed in order to minimize these hazards: Location: entire site On or about: 5/18/15 a) Employees, exposed to fall hazards while engaged in carpentry work, were not provided with adequate fall protection training. The Koibil Construction Corporation was previously cited for a violation of this occupational safety and health standard or its equivalent standard 1926.503(a)(1), which was contained in OSHA inspection number 1012116, citation number 1, item number 2b and was affirmed as a final order on 1/20/2015, with respect to a workplace located at 33 Maple Ave., Greenwich, CT. |
|
|