| Inspection Type |
Planned
|
| Scope |
Complete
|
| Safety/Health |
Safety
|
| Close Conference |
2013-06-27
|
| Emphasis |
N: SSTARG12, P: SSTARG12
|
| Case Closed |
2018-06-04
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100022 C |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
500.0 |
| Initial Penalty |
3080.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
4 |
| Nr Exposed |
6 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.22(c): Covers and/or guardrails were not provided to protect personnel from the hazards of open pits, drains, tanks, vats, ditches, etc.: a) Frying Room, on or about 6/27/13: Grating was missing in two areas over the floor drain in front of the fryer leaving a 11" X 14" hole and a 7" X 14" hole. b) Potato Peeling Room, on or about 6/27/13: Grating was missing in two areas over the floor drain in front of the potato peeling equipment leaving a 5" X 14" hole and a 6" X 14" hole. Abatement certification must be submitted for these items. |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19100023 C01 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
500.0 |
| Initial Penalty |
3850.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
4 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.23(c)(1): Open-sided floors and/or platforms four feet or more above adjacent floor or ground level were not guarded with standard railings: a) Bagging Room, on or about 6/27/13: Standard guardrails were missing at one end of a catwalk, approximately 7 feet from floor level and the pipe railing on the back side was bent and disconnected. Abatement certification must be submitted for this item. |
|
| Citation ID |
01003A |
| Citaton Type |
Serious |
| Standard Cited |
19100036 D01 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
500.0 |
| Initial Penalty |
3850.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
10 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.36(d)(1): An exit door must be unlocked: a) Back Garage, on or about 6/27/13: Exit door was locked. Abatement certification must be submitted for this item. |
|
| Citation ID |
01003B |
| Citaton Type |
Serious |
| Standard Cited |
19100037 A03 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
10 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.37(a)(3): Exit route(s) were not kept free and unobstructed: a) Back Garage, on or about 6/27/13: The path to the front exit door was blocked by a mower and scrap metal pieces and the path to the public way outside the door was blocked by plastic containers of used oils. Abatement certification must be submitted for this item. |
|
| Citation ID |
01003C |
| Citaton Type |
Serious |
| Standard Cited |
19100037 A04 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
2310.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
3 |
| Nr Exposed |
10 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.37(a)(4): Safeguard(s) designed to protect employees during an emergency (e.g., sprinkler systems, alarm systems, fire doors, exit lighting), were not in proper working order at all times: a) Back Garage/Back Warehouse, on or about 6/27/13: The exit sign lighting was not working over the front exit door. b) Back Garage, on or about 6/27/13: The exit sign lighting was not working over the back exit door and the exit door was stuck, coming off its hinges and would not close properly after being opened. Abatement certification must be submitted for these items. |
|
| Citation ID |
01005 |
| Citaton Type |
Serious |
| Standard Cited |
19100110 E04 III |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
250.0 |
| Initial Penalty |
3080.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
10 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.110(e)(4)(iii): Permanent and removable fuel containers were not securely mounted to prevent jarring loose, slipping, or rotating: a) Back Garage, on or about 6/27/13: A LP gas container on a Nissan forklift was not secured to prevent jarring loose, slipping or rotating in that both safety latches were broken. Abatement certification must be submitted for this item. |
|
| Citation ID |
01006 |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C04 I |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
500.0 |
| Initial Penalty |
5390.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
2 |
| Nr Exposed |
3 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) Bagging Room, on or about 6/27/13: Lockout procedures were not being utilized in that an employee was cleaning the inside of a Hayssen bagging machine without locking out the energy sources on the machine. b) Bagging Room, upper mezzanine, on or about 6/27/13: Lockout procedures were not being utilized in that two employees were cleaning the vibratory conveyor and chutes without locking out the energy sources to the machine. Abatement documentation must be submitted for these items. |
|
| Citation ID |
01007 |
| Citaton Type |
Serious |
| Standard Cited |
19100157 C04 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
250.0 |
| Initial Penalty |
2310.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
3 |
| Nr Exposed |
4 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.157(c)(4): Portable fire extinguishers were not maintained in a fully charged and operable condition: a) Back Garage, on or about 6/27/13: A Buckeye portable fire extinguisher on a Nissan forklift was discharged. b) Back Garage, on or about 6/27/13: There were two portable fire extinguishers located on the floor near the back exit door that were discharged. Abatement certification must be submitted for these items. |
|
| Citation ID |
01008 |
| Citaton Type |
Serious |
| Standard Cited |
19100219 C04 II |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
500.0 |
| Initial Penalty |
3080.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(c)(4)(ii): The unused keyway(s) of projecting shaft end(s) were not filled up or covered: a) Potato Unloading Area, on or about 6/27/13: Projecting shaft end with keyway driving the conveyor was not guarded. Abatement certification must be submitted for this item. |
|
| Citation ID |
01009A |
| Citaton Type |
Serious |
| Standard Cited |
19100303 B02 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
500.0 |
| Initial Penalty |
3080.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
2 |
| Nr Exposed |
10 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling: a) Frying Room, on or about 6/27/13: The on/off switch to a Lasko fan was rewired to the outside of the frame of the fan and hanging by wires and not being used in accordance with the listing or labeling. b) Bagging Room, on or about 6/27/13: An orange extension cord was wired directly into the motor for the takeout conveyor with the grounding wire sticking out. Cord was not being used in accordance with the listing and labeling. Abatement certification must be submitted for these items. |
|
| Citation ID |
01009B |
| Citaton Type |
Serious |
| Standard Cited |
19100304 G05 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
3 |
| Nr Exposed |
10 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.304(g)(5): The path to ground from circuits, equipment, and enclosures was not permanent, continuous, and effective: a) Frying Room, on or about 6/27/13: A Lasko box fan was not grounded in that it was only a two wire cord. b) Bagging Room, on or about 6/27/13: The takeout conveyor was not grounded in that an orange extension cord was wired directly into a junction box on the motor for the conveyor and the grounding wire was not attached. c) Bagging Room, on or about 6/27/13: A Max Performance pedestal fan was not grounded in that the ground pin was missing from the plug end. Abatement certification must be submitted for these items. |
|
| Citation ID |
01009C |
| Citaton Type |
Serious |
| Standard Cited |
19100303 B08 I |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
2310.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.303(b)(8)(i): Electrical equipment was not firmly secured to the surface on which it was mounted: a) Production Shop Area, on or about 6/27/13: An electrical disconnect switch box for the battery charger was not secured in place. Abatement certification must be submitted for this item. |
|
| Citation ID |
01011 |
| Citaton Type |
Serious |
| Standard Cited |
19100303 G02 I |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
500.0 |
| Initial Penalty |
5390.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
2 |
| Nr Exposed |
2 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.303(g)(2)(i): Live parts of electric equipment operating at 50 volts or more were not guarded against accidental contact by use of approved cabinets or other forms of approved enclosures or by any of the means identified in paragraphs (A), (B), (C), and (D) of 29 CFR 1910.303(g)(2)(i): a) Frying Room, on or about 6/27/13: A 220 volt electrical panel was open where employees are required to access the starter control for the salter which is located inside the panel, exposing employees to live electrical parts. b) Area across from Frying Room, on or about 6/27/13: A 110 volt control panel for the stretch wrap machine had the cover removed, exposing live electrical parts. Abatement documentation must be submitted for these items. |
|
| Citation ID |
01012A |
| Citaton Type |
Serious |
| Standard Cited |
19100305 G01 IV A |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
250.0 |
| Initial Penalty |
2310.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
3 |
| Nr Exposed |
10 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.305(g)(1)(iv)(A): Flexible cords and/or cables were used as a substitute for the fixed wiring of a structure: a) Production Shop Area, on or about 6/27/13: Extension cords providing current to a stretch wrap machine were strung overhead and being used as permanent wiring. b) Bagging Room, on or about 6/27/13: Extension cord providing current to a fan being used inside the Hayssen bagger #3 was being used as permanent wiring. c) Bagging Room, on or about 6/27/13: Flexible cords providing current to the low level feeder was strung up overhead and being used as permanent wiring. Abatement certification must be submitted for these items. |
|
| Citation ID |
01012B |
| Citaton Type |
Serious |
| Standard Cited |
19100305 G02 III |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
2310.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
5 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.305(g)(2)(iii): Flexible cords were not connected to devices and fittings so that tension would not be transmitted to joints or terminal screws: a) Production Shop Area, on or about 6/27/13: Flexible cord for the battery charger was pulled loose from the plug fitting, no strain relief provided. Abatement certification must be submitted for this item. |
|
| Citation ID |
01014A |
| Citaton Type |
Serious |
| Standard Cited |
19101200 F05 I |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
250.0 |
| Initial Penalty |
2310.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
6 |
| Nr Exposed |
5 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.1200(f)(5)(i): The employer did not ensure that each container of hazardous chemicals in the workplace was labeled, tagged or marked with the identity of the hazardous chemical(s) contained therein: a) Back Garage/Warehouse Area, on or about 6/27/13: There were five blue barrels/containers of oils located outside the exit door that were not labeled as to the identity of the contents contained therein. b) Garage Area, on or about 6/27/13: There were numerous containers of liquids in red plastic containers and five gallon pails located near the back exit door that were not labeled as to the identity of the contents contained therein. Abatement certification must be submitted for these items. |
|
| Citation ID |
01014B |
| Citaton Type |
Serious |
| Standard Cited |
19101200 F05 II |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
6 |
| Nr Exposed |
5 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.1200(f)(5)(ii): The employer did not ensure that each container of hazardous chemicals in the workplace was labeled, tagged or marked with the appropriate hazard warnings: a) Back Garage/Warehouse Area, on or about 6/27/13: There were five blue barrels/containers of oils located outside the exit door that were not labeled as to their appropriate hazard warnings. b) Garage Area, on or about 6/27/13: There were numerous containers of liquids in red plastic containers and five gallon pails located near the back exit door that were not labeled as to their appropriate hazard warnings. Abatement certification must be submitted for this item. |
|
| Citation ID |
02001 |
| Citaton Type |
Repeat |
| Standard Cited |
19100022 A01 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
1500.0 |
| Initial Penalty |
4620.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
10 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms or service rooms were not kept clean and orderly or in a sanitary condition: a) Truck Shop, on or about 6/27/13: Poor housekeeping throughout the shop in that containers, parts, equipment, tools, trash, etc. were laying on the floor. Abatement documentation must be submitted for this item. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 1a and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. |
|
| Citation ID |
02002 |
| Citaton Type |
Repeat |
| Standard Cited |
19100147 C07 I |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
3000.0 |
| Initial Penalty |
10780.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
30 |
| Nr Exposed |
30 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(7)(i): The employer did not provide training to ensure that the purpose and function of the energy control program were understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls were acquired by employees: a) At the establishment, on or about 6/27/13: Training was not provided to all authorized and affected employees on the lockout/tagout program and procedures to ensure that employees acquired the knowledge and skills required for the safe application, usage and removal of the energy controls and that the purpose and function of the energy control program was understood by employees. Servicing and/or maintenance is performed by employees on various pieces of equipment, including, but not limited to fryer, cardboard baler, bagging machines, waste water settling tanks, etc. Abatement documentation must be submitted for this item. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 2b and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. |
|
| Citation ID |
02003 |
| Citaton Type |
Repeat |
| Standard Cited |
19100176 B |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
2000.0 |
| Initial Penalty |
7700.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
4 |
| Nr Exposed |
10 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.176(b): Material stored in tiers was not stacked, blocked, interlocked or limited in height so that it was stable and secure against sliding and collapse: a) Shipping & Receiving Area, Bread Room, on or about 6/27/13: Pallets of cardboard boxes were not secure and stable against sliding and collapse. b) Back Warehouse, on or about 6/27/13: A pallet of boxes of paper records on the storage rack was not secure and stable from sliding and collapsing. c) Back Garage, Warehouse Area, on or about 6/27/13: Pallets of carley canisters were not secure and stable from sliding and collapse. d) Back Garage, Warehouse Area, on or about 6/27/13: Pallets of cardboard boxes were not secure and stable against sliding and collapse. Abatement documentation must be submitted for these items. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 4 and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, New York. |
|
| Citation ID |
02004 |
| Citaton Type |
Repeat |
| Standard Cited |
19100212 A01 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
3000.0 |
| Initial Penalty |
10780.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
4 |
| Nr Exposed |
10 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.212(a)(1): Machine guarding was not provided to protect operator(s) and other employees from hazard(s) created by rotating parts and ingoing nip points: a) Potato Unloading Area, on or about 6/27/13: Ingoing nip points on the truck unload conveyor belt and idler pulleys in two areas were not guarded. b) Frying Room, on or about 6/27/13: Salter on fryer, rotating spinner shaft at the salter and ingoing nip points at the takeaway conveyor were not guarded. c) Bagging Room, on or about 6/27/13: Ingoing nip points on a conveyor belt were not guarded in that sections of the plastic conveyor belting were broken and missing creating a nip point hazard. d) Bagging Room, on or about 6/27/13: Ingoing nip points on an inclined conveyor belt and sprocket at the discharge end onto a turntable for the Hayssen bagging machine #3 were not guarded. Abatement documentation must be submitted for these items. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 5 and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, New York. |
|
| Citation ID |
02005 |
| Citaton Type |
Repeat |
| Standard Cited |
19100212 A03 II |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
2000.0 |
| Initial Penalty |
7700.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
2 |
| Nr Exposed |
6 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): a) Bagging Room, on or about 6/27/13: Point of operation on a Hayssen bagging machine #5 was not guarded where the jaws close to seal and cut each bag, in that the interlocked doors were missing. b) Bagging Room, on or about 6/27/13: Point of operation on a Hayssen bagging machine #3 was not adequately guarded in that the right door was open and the interlock was not functioning on the door. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 6 and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. Abatement documentation must be submitted for this item. |
|
| Citation ID |
02006 |
| Citaton Type |
Repeat |
| Standard Cited |
19100212 A04 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
2000.0 |
| Initial Penalty |
7700.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.212(a)(4): Revolving drum(s), barrel(s), or container(s) were not guarded by enclosure(s) which were interlocked with the drive mechanism so that the barrel(s), drum(s), or container(s) could not revolve unless the enclosure(s) were in place: a) Frying Room, on or about 6/27/13: Revolving tumbler in the wash tank located before the fryer was not guarded. Abatement documentation must be submitted for this item. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 7 and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. |
|
| Citation ID |
02007A |
| Citaton Type |
Repeat |
| Standard Cited |
19100219 D01 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
2000.0 |
| Initial Penalty |
6160.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a) Bagging Room, on or about 6/27/13: Pulleys driving a turntable at the Hayssen bagging machine #3 were not guarded. Abatement documentation must be submitted for this item. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 8a and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. |
|
| Citation ID |
02007B |
| Citaton Type |
Repeat |
| Standard Cited |
19100219 E01 I |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs 42 inches or less from the floor level were not fully enclosed by guards conforming to requirements specified in 29 CFR 1910.219(m) and (o): a) Bagging Room, on or about 6/27/13: A leather riveted belt driving a turntable at the Hayssen bagging machine #3 was not guarded. Abatement documentation must be submitted for this item. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number 312372170, Citation number 1, Item number 8a and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. |
|
| Citation ID |
02008 |
| Citaton Type |
Repeat |
| Standard Cited |
19100219 F03 |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
2000.0 |
| Initial Penalty |
7700.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
2 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven -7 feet or less above floors or platforms were not enclosed: a) Frying Room, on or about 6/27/13: Chain and sprockets driving the orienting rolls before the tumbler washer were not guarded. b) Bagging Room, on or about 6/27/13: Chain and sprocket driving the conveyor belt from the Hayssen bagging machine #3 to the turntable located at floor level was not guarded. Abatement documentation must be submitted for these items. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard, which was contained in OSHA inspection number312372170, Citation number 1, Item number 9 and was affirmed as a final order on 12/18/09, with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. |
|
| Citation ID |
02009 |
| Citaton Type |
Repeat |
| Standard Cited |
19100303 B07 IV |
| Issuance Date |
2013-12-20 |
| Abatement Due Date |
2014-06-01 |
| Current Penalty |
2000.0 |
| Initial Penalty |
7700.0 |
| Contest Date |
2014-01-10 |
| Final Order |
2015-06-09 |
| Nr Instances |
2 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.303(b)(7)(iv): There were damaged parts that may adversely affect safe operation or mechanical strength of the equipment, such as parts that are broken, bent, cut, or deteriorated by corrosion, chemical action or overheating. a) Frying Room, on or about 6/27/13: Flexible conduit was pulled loose from the motor fitting for the tumbler. b) Frying Room, on or about 6/27/13: An electrical disconnect switch for the slicer located along the back wall behind the fryer was rusted out on the bottom exposing electrical conductors. Abatement documentation must be submitted for these items. The Terrell's Potato Chip Co., Inc. was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard which was contained in OSHA inspection number 312372170, Citation number 2, Item number 2 and was affirmed as a final order on 12/18/09 with respect to a workplace located at 218 Midler Park Drive, Syracuse, NY. |
|
|
